qtforum.de

Code: Alles auswählen

m_pWidgetLayout = new QVBoxLayout(this);
	
	m_pLayout = new QGridLayout(this);
	
	m_pLayout->addWidget(new QLabel("Datenquelle",this),0,0);
	m_pLE_wSource = new SourceWidget(this);
	m_pLE_wSource->setValue(m_pStructure->wSource);
	m_pLayout->addWidget(m_pLE_wSource,0,1);
	connect(m_pLE_wSource,SIGNAL(valueChanged()),this,SLOT(sourceChanged()));

	m_pLayout->addWidget(new QLabel("min. Sensorbereich",this),1,0);
	m_pLE_cSensorMin = new QLineEdit(this);
	m_pLE_cSensorMin->setText(QString().setNum(m_pStructure->cSensorMin));
	m_pLayout->addWidget(m_pLE_cSensorMin,1,1);

	m_pLayout->addWidget(new QLabel("max. Sensorbereich",this),2,0);
	m_pLE_cSensorMax = new QLineEdit(this);
	m_pLE_cSensorMax->setText(QString().setNum(m_pStructure->cSensorMax));
	m_pLayout->addWidget(m_pLE_cSensorMax,2,1);

	m_pLabelcRefValue = new QLabel(tr("Verstärkungsfaktor der CAN-DATEN"),this);
	m_pLayout->addWidget(m_pLabelcRefValue ,3,0);
	m_pLE_cRefValue = new QLineEdit(this);
	//m_pLE_fStuetz->setText(QString().setNum(m_pStructure->fStuetz));
	m_pLayout->addWidget(m_pLE_cRefValue,3,1);
	
	m_pDiagramRefValue = new DiagramWidget(this,tr("Stützpunkte auf der Kennlinie")); // wird nicht automatisch angezeigt
	QStringList values;
	QStringList names;
	
	for(int i = 0; i < 6; i++)
	{
		values << QString().setNum(m_pStructure->cRefValue[i]);
		names << QString("Stützpunkt %1").arg(i);
	}
	
	m_pDiagramRefValue->setValues(names,values);
	
	m_pLabelStuetz = new QLabel(tr("Nachrichtentimeout"),this);
	m_pLayout->addWidget(m_pLabelStuetz ,4,0);
	m_pLE_fStuetz = new QLineEdit(this);
	//m_pLE_fStuetz->setText(QString().setNum(m_pStructure->fStuetz));
	m_pLayout->addWidget(m_pLE_fStuetz,4,1);
	
	m_pDiagramStuetz = new DiagramWidget(this,tr("Stützpunkte auf der Kennlinienabschnitte")); // wird nicht automatisch angezeigt
	for(int i = 0; i < 6; i++)
	{
		values << QString().setNum(m_pStructure->fStuetz[i]);
		names << QString("Stützpunkt %1").arg(i);
	}
	
	m_pDiagramStuetz->setValues(names,values);
	
	m_pLayout->addWidget(new QLabel("Offset",this),5,0);
	m_pLE_fOffset = new QLineEdit(this);
	m_pLE_fOffset->setText(QString().setNum(m_pStructure->fOffset));
	m_pLayout->addWidget(m_pLE_fOffset,5,1);

	m_pLayout->addWidget(new QLabel("Empfangs ID",this),6,0);
	m_pLE_dwCanID = new QLineEdit(this);
	m_pLE_dwCanID->setText(FormatConv::longToHex(m_pStructure->dwCanID));
	m_pLayout->addWidget(m_pLE_dwCanID,6,1);

	m_pLayout->addWidget(new QLabel("Verzögerungszeit der Sensorprüfung Basis 500ms",this),7,0);
	m_pLE_cCheckDelay = new QLineEdit(this);
	m_pLE_cCheckDelay->setText(QString().setNum(m_pStructure->cCheckDelay));
	m_pLayout->addWidget(m_pLE_cCheckDelay,7,1);
	
	OkButton *pOKButton = new OkButton(this);
	m_pLayout->addWidget(pOKButton,8,1);
	
	connect(pOKButton,SIGNAL(clicked(bool)),this,SLOT(saveValues(bool)));
	
	// layout
	m_pWidgetLayout->addLayout(m_pLayout);
	
	m_pWidgetLayout->addWidget(m_pDiagramRefValue);
	m_pDiagramRefValue->hide();
	
	m_pWidgetLayout->addWidget(m_pDiagramStuetz);
	m_pDiagramStuetz->hide();
	
	setLayout(m_pWidgetLayout);

Code: Alles auswählen

if(m_pLE_wSource->indexOfEingang() > 1)
	{
		// es wurden io eingänge ausgewählt, also werden die diagramme angezeigt
		m_pLabelcRefValue->hide();
		m_pLabelStuetz->hide();
		m_pLE_cRefValue->hide();
		m_pLE_fStuetz->hide();
		
		m_pDiagramRefValue->show();
		
		m_pDiagramStuetz->show();
	}
	else
	{
		m_pLabelcRefValue->show();
		m_pLE_cRefValue->show();
		
		m_pLabelStuetz->show();
		m_pLE_fStuetz->show();
		
		
		
		m_pDiagramRefValue->hide();
		m_pDiagramStuetz->hide();
	}
	
	m_pLayout->update();
	m_pWidgetLayout->update();